Flyfishing, flytying and hooks
Home » 2013 (Page 13)

First Seatrout on fly

OLYMPUS DIGITAL CAMERABack when I was a kid I used to fish a lot (a serious amount!), and my only seatrout ever taken must have been when I was 10-12 years: it was taken on a lure and weighed in at a hefty 2kg! Since then I haven’t taken any seatrout, and since I picked up flyfishing a couple of years back I have never tried much to target them. This year, however, I find myself wanting to expand the (freshwater) trout-season in Oslo, so I have started tying up some flies for saltwater (zonkers, baitfish) to go around the Oslo fjord area targeting seatrout.

On friday after work I got on the bus and headed out to a spot that is supposedly seatrout area. On the second throw two mackerels followed in after my white zonker and on the fifth cast a seatrout was on! Frankly I was a bit shocked when the trout suddenly sprang 50cm up into the air and raced towards land so I never had a chance to keep a tight line. I never landed that one…..

During the afternoon I had several fish very interested in the baitfish, and they were even hitting it and following it in towards land, but nothing actually was hooked. Finally I got this little seatrout on a baitfish, and it had the same behaviour as the first: raced towards land so I ended up with half my line in a tangle after I landed it, but it did end up in my net! So: first ever seatrout on fly, not a big one, but a good start for the winter season here in Oslo.

I put on the orange Rabbit Zonker towards the end and I had one fish on that did the classic *thug-thug*, never hooked properly, and was gone…. That one must have been 1kg plus, but I don’t know if it was a seatrout, so I might head out there again tomorrow to see if it still is in the area!

OLYMPUS DIGITAL CAMERACan’t complain about the weather on days like this….

OLYMPUS DIGITAL CAMERA

 

 

Rabbit Zonkers

dryfly.me.2013.09.rabbit_zonker_1

Hook: Dai-Riki 899 #6
Thread: UNI 6/0 Black
Tail/Body: Single strip of Rabbit Zonker, Tan

Never worked with Zonkers before, but this might be the simplest one yet: a single strip of Rabbit zonker, wrapped around the hook, tied in with thread. I fished this last weekend and got myself a Pollock, so I know it works. The Zonker really flows in the water: the tail and the body hair on this makes for very fluid motion. Of course I had to get a couple of other colors for the sea-trout fishing I’m going for this weekend.

dryfly.me.2013.09.rabbit_zonker_2

dryfly.me.2013.09.rabbit_zonker_3

 

SBS: Baitfish

dryfly.me.2013.09.bait_fish_10Hook: TMC 811S #6
Thread: UNI 6/0 Black
Tail: Hareline Extra Select Craft Fur White, Angel Hair
Body: Hareline Solid Tinsel Chenille Pearl
Wing: Hareline Extra Select Craft Fur White/Black
Head: Hareline Adhesive Holographic Eyes 3/16 Red, Bug-Bond

I have fished some in saltwater before, but haven’t had much luck when it comes to actually catching anything(!?!). But: I was on vacation last week and ended up when the tidal went out underneath a bridge, causing a strong current where I spotted a lot of fish. I put on this baitfish on my #6 rod and got 30minutes of Mackerel fun: pulling in fast I saw the mackerel hitting this fly hard! More pictures on that later, but this is my take on a baitfish pattern that was very successful. It becomes quite slim in the water and should trigger the fish if pulled in fast high in the water

Add a loop of mono at the end of the hook, I use quite a thick one

dryfly.me.2013.09.bait_fish_1Tie in craft fur above the guard

dryfly.me.2013.09.bait_fish_2Tie off the craft fur properly ( the fish might hit this fly hard )

dryfly.me.2013.09.bait_fish_3Add some angel hair (not needed, but adds some glimmer to the fly)

dryfly.me.2013.09.bait_fish_4Tie in the tinsel

dryfly.me.2013.09.bait_fish_5Wrap the tinsel, forming a body. I don’t mind much if the body is even or straigth

dryfly.me.2013.09.bait_fish_6Add more white craft fur as underwing

dryfly.me.2013.09.bait_fish_7Add black craft fur as top-wing and tie of the fly with a decent head since you want a place to glue on the eyes. I vary between black, brown and  green for the top-wing to create variations

dryfly.me.2013.09.bait_fish_8I use some zap-a-gap to glue  the eyes to the thread

dryfly.me.2013.09.bait_fish_9Apply bug-bond to form a head

dryfly.me.2013.09.bait_fish_10The material needed for this fly

OLYMPUS DIGITAL CAMERA